As an Amazon Associate, I earn from qualifying purchases. We only endorse products that we have researched thoroughly and will be of use to our readers.
This Lotos ltp5000D review will cover some of the main features that we have found to make this one of the best plasma cutters on the market.
The Lotos ltp5000D has the latest high-frequency inverter technology that uses IGBT to give a greater non-invariant, equipped, and high precision current to cutting base.
The technology has been greatly minimized in weight and size of inverter plasma cutters. The machine aids in just achieving smooth and clean cuts of a variety of surfaces and materials like brass and aluminum.
The cutters are designed mostly to be applied in businesses and self-utility services that are professionally trained to operate.
It delivers an unyielding cut when in compact packages. It got a pilot arc characteristic that is necessary for non-stop cutting on rough faces or dirty metal.
If we apply switch power inverter technology, the parameters of the main transformer are usually lowered, and the efficiency shifts up to 30%.
The LTP5000D is the best choice for small home duties and small businesses, (although if you are cutting day in, day out, you may want to consider a much higher-end version, like those here (expensive).
See also: Best plasma cutters under $500
Lotos LTP5000D Review, What We Enjoyed About This Plasma Cutter
A good plasma cutter has got a handle for portability. It uses a less harmful compressed gas to cut these materials; copper, aluminum, mild steel, alloy steel, and stainless steel. Therefore, it does not endanger the life of the user.
It hence enables you to have smooth and clean surfaces using less heat and without destroying the metal. It has got a lightweight. Consequently, it is easy to carry around.
Pilot arc torch smoothly cuts the rough, painted, and even rusty faces of materials. It is not restricted to a particular material. It is efficient in that it does all these using a minimum power input. Also, after cutting the material, the immediate surface is elegant and doesn’t file.
The plasma cutter uses a MOSFET transistor. This is what offers a constant output.
By doing so, you can cut a very thin metal neatly and smoothly. When cutting a slightly thicker metal surface or material, the transistor helps you to use a uniform high power output from the machine.
Dual Voltage Capabilities
This characteristic enables the machine to run smoothly both on 220 volts 50/60 hertz frequency power and on 110 volts50/60 hertz using a device called pig-digital. This helps the user not to worry about the power consumption of the machine.
This is because the above voltage is single phase AC and is always readily available even in the households. Depending on the material you are cutting you just choose the voltage you want to apply.
Sharp Cutting Performance
Pilot Arc Plasma Cutter provides adamant cutting ability in compacted pack. It is, therefore, important when it comes to dealing with very rough surfaces and dirty metals.
If you optimize it, then you can use it to cut thick metals, as well as providing a uniform output for cutting thin metals at the same time.
This is what we term as a multi-performance feature that shows how the machine is not restricted to cutting specific metal types.
Pros and Cons
- Automatic dual voltage and frequencies of 220v 50/60 Hz and 110v 50/60Hz.
- It provides fast and smooth cutting even on thick and dirty metals.
- It has got and handles hence portable and light in weight.
- The employment of switch power inverter technology gives fewer dimensions and weight and the efficiency increased by 30%.
- It offers minimum heat input hence avoiding distortion of metal under the cut.
- It does not last longer, fails after the 2-4th attempt.
- Repair parts not available still.
- It is noisy.
Frequently Asked Questions (FAQs)
How is air connection made?
There is a barbed fitting at the back of the unit where you push a hose over and secure it with a hose clamp.
Does the unit have any air filter in it?
Yes, the unit comes with a small canister filter.
For cutting an average of 1/6 to 1/3 mild steel what’s the perfect air pressure that should be applied to the machine?
To get a cleaner cut I recommend you with 75 psi for up to 1/4. The speed and cleaning tips also matter a lot.
This is an excellent type of a cutter that is not too much costly compared to other types in the market. It is capable of giving strong cutting abilities and also can cut any metal; rough, painted and rusty surface.
It also helps you achieve clean and smooth cuts of various materials. More than 2,000 customers have reviewed this item, and 70% of them have given it a rating of 4.5-star and above. This is a greater indication of how important it is.
Amazon and the Amazon logo are trademarks of Amazon.com, Inc, or its affiliates.